
Speed bunp assembly: steps for a complete street set
A properly made speed bunp mount holds the modules firmly on the roadway and keeps the slowing effect years in a row. The complete 2–6 meter street sets include the middle elements and the heads, so you only prepare the right surface, anchors and tools.
In short: choose the set after the width of the street, clean the surface, draw the line, holes, fix the modules and check the regular gathering.
Do you need help choosing?
Tell us what you need and we'll send you the offer on the same working day.
A complete set of limiters greatly shorten the work, because you get the right middle elements and heads from the start. The result depends, however, on the preparation of the surface, the correct alignment and the suitable catch for asphalt or concrete. On public roads, ask the administrator's opinion first. See the rubber sets and Ustun kits in the Speed bunps category and choose the right length.
One mounting speed bump successfully starts with the right set and continues with a well-prepared surface. Many buyers focus only on the modules themselves. However, catching and aligning decide how long the limiter can hold under wheels. In this guide we focus, therefore, on the complete street settings. We see what they contain, how you prepare the land and what you check after installation.
What contains a complete set for speed bunp mounting
A street set gathers middle elements and two heads. The ends close the edge limiter and offer a smoother side ramp. Category Speed bump sets You actually find two families.
Rubber sets with modules 500x600x45 mm
These sets have yellow reflective films. For example, 2 meter street set contains 2 modules 500x600x45 mm and 2 heads 300x600x45 mm. The total length thus reaches 1.6 metres.
- 3 metres – 4 modules and 2 heads, total 2.6 m;
- 4 metres – 6 modules and 2 heads, total 3.6 m;
- 5 metres – 8 modules and 2 heads, total 4.6 m;
- 6 meters – 10 modules and 2 heads, total 5.6 m.
Therefore, the installed length remains slightly below the nominal width of the street. At speed bunp mounting, the difference leaves room for rows and water flow. For example, the 3-metre set occupies 2.6 m and leaves a margin on each side.
Plastic UT 9020 UT Kits
The Ustun family uses UT 9020 modules of 250x350x50 mm. Kits cover 2, 3, 4, 5 and 6 meters. Among him, Ustun kit for 3 meters It fits well with the block alleys. In addition, compatible heads, such as cap UT 9021 yellow, the same height as 50 mm.
Before mounting speed bunp: checks
First, clarify the status of the road. For a public street you need the consent of the road manager. Road legislation you find on National legislative portal. Instead, in private parking lots and premises decide the owner.
Then choose the position. For a safe speed pump mounting, avoid channel caps, drain mouths and tight curves. Also check if cables or pipes are passing under the surface. At the same time, a limiter placed too close to an intersection surprises drivers. Let them, therefore, time to see him.
Surface preparation: asphalt or concrete
When mounting speed bunp, the surface decides to catch. Thus, you treat asphalt and concrete differently.
- Asphalt – needs longer anchors, because the material is easily yielding to the heat.
- Concrete – Keeps good dibs or chemical anchors, but the hole requires proper burghiu.
- Paves – can be moved; in this case check the stability of the bed before.
Clean the area of dust, oil and gravel. Then let the surface dry completely. The wet asphalt reduces the adhesion of any adhesive used.
Tools and materials for installing speed bunp
Prepare everything before closing the circulation tape. Thus, the work takes a little time and disturbs traffic less.
- an asphalt or concrete rotor and nozzles suitable for use;
- anchors or screws with dilutes, chosen after the surface;
- key for clamping, to be preferred with cliché;
- chalk or strand for alignment;
- blower or air pump, to clean holes;
- signs or signals for the working area.
It shall also check whether the set includes the catch elements. If not, buy suitable anchors for the thickness of the modules and the type of surface.
Steps of mounting speed bump
After you've prepared the tools, follow the steps below.
- Draw a line perpendicular to the road axis with chalk.
- So dry the modules and heads, without grip, for verification.
- Mark the holes through the module holes.
- Lift the modules and give the holes to the depth required by the anchors.
- Blow the dust out of the holes so that the catch can work at full length.
- Reset the modules and tighten the anchors gradually, from the middle to the heads.
Thus, avoid one end to rise while tightening the other. In addition, the gradual tightening keeps the alignment. In other words, a patient speed bunp mount looks straight and lasts longer.
Color alternation and visibility
Rubber sets already have yellow films. In the Ustun kits, however, you alternate yellow and black modules. For example, Ustun kit for 2 meters more visible with regular rotation. For unlit streets, add a warning indicator as required by local requirements.
Checks after mounting speed bunp
The first test you do with a car, at low speed. Listen if the modules crawl or move. Then check if the water flows freely near the heads.
- after the first week, review the anchors' tightening;
- monthly, clean the stone locked between modules;
- immediately replaces a broken end because it leaves the edge of the exposed modules.
Long-term maintenance
Winter, the snow plug can hang the edges. Therefore, signal the limiter before the cold season. At the same time, check the spring for a way out.
Wet modules are replaced individually, without changing the whole set. Thus, a well-maintained speed boom assembly remains complete years in a row.
For other traffic problems, see speed limiters sold in pieces. If cables cross the road, combine the set with a category pass Cable protection.
Frequently Asked Questions about Speed Bump Mounting
Can I do the assembly myself?
Yes, in private premises, if you have the right rotor and anchors. However, for the public road you need advice.
What set do I choose for a five-meter street?
The 5-metre rubber set covers 4.6 m. So, I'm left free for the water to drain.
Can I lengthen an existing set?
Yes, add mid-size modules of the same size. Then move the heads to the new edges.
For a simple and safe speed bunp assembly, choose the right set from the category Speed bump sets. The Blocator.ro team helps you set the length and type of modules.



















